Aluminum Machining Supplier

Product Item: Aluminum Machining Supplier
Category: Aluminum Machining
Aluminium machining , using cold and hot processing methods to process aluminum billet into parts, the main methods are turning, stamping, sheet metal, rolling, extrusion, stretching and forging.

Project
Aluminium machining , using cold and hot processing methods to process aluminum billet into parts, the main methods are turning, stamping, sheet metal, rolling, extrusion, stretching and forging. Aluminium products processing, Aluminium pieces Machining, Aluminium alloy Machining, Aluminium surface treatment, Aluminium parts finishing, Aluminium shell Machining, Aluminium radiators, Aluminium bars Knurling...

Crafts
During the processing of aluminum thin-walled cavity parts, comprehensive considerations are taken into consideration in terms of optimization of process flow, heat treatment, improvement of clamping methods, and high-speed cutting processing. In combination with the structural characteristics of parts, reasonable Process flow and processing solutions are formulated.
1. The aluminum processing process can separate rough and finish machining. After rough machining is completed, heat treatment is performed on the part to fully release the cutting stress and residual stress of the part. After the finish machining, the machining quality of the part will be greatly improved. The implementation of rough and fine processing separately has the following advantages:
(1) Reduce the effect of residual stress on the deformation of aluminum processing. After the roughing is completed, the heat treatment can be used to remove the stress generated by the roughing of the part and reduce the influence of the stress on the finishing quality.
(2) Improve aluminum processing accuracy and surface quality. Coarse and fine processing are separated, and the precision machining is only a small amount of machining allowance, resulting in less processing stress and deformation, and can greatly improve the quality of parts.
(3) Improve production efficiency. Since rough machining removes only excess material and leaves a sufficient margin for finishing, it is not enough to consider dimensions and tolerances, effectively exert the performance of different types of machine tools, and improve cutting efficiency.
2.Aluminum processing heat treatment:
After the parts are cut and processed, the metal structure will undergo great changes. In addition, the effect of cutting movement will produce large residual stresses. In order to reduce the deformation of the parts, the residual stress of the materials must be fully released. Aluminum alloy thin-walled cavity parts generally use low-temperature annealing heat treatment.
3, improve the aluminum processing and clamping method:
In the processing of ordinary parts, the clamping method is usually used to set the bench vise. circular element may be employed chuck clamping manner, whether bench vise or chuck clamping fixture, will produce different degrees of clamping stress. The clamping stress and the elastic restoration after the part is removed will cause the part to have a certain deformation. In the roughing stage, because only the excess material is removed, the bench vise clamp can be used.
4, high-speed cutting aluminum processing:
During the cutting process, the main factors affecting the surface quality of the workpiece are the built-up edge of the built-up edge, the phosphatization, the vibration and the sharpening quality of the cutting edge, the defect of the workpiece material, and the use of the cutting fluid. High-speed cutting compared with ordinary cutting, cutting degree of the block, the material deformation speed, the strain rate is small, does not produce built-up edge, phosphorous thorn.

Precautions
The commonly used aluminum processing methods are: casting, cold rolling, cold drawing, cold forging, cold extrusion, stamping, etc.; in the actual production work, we also commonly encounter some aluminum alloy cutting processing such as: turning, drilling Boring, boring, milling, planing, broaching, and sawing. The aluminum material is soft and highly malleable. After machining, the aluminum parts are deformed to varying degrees due to internal stresses, cutting heat, and the influence of the fixtures. To ensure the forming quality of the parts and to control the deformation, it is necessary to handle Methods include:
(1) In the milling process, whether it is rough milling or precision milling, the part should be symmetrically processed and turned several times so that the stresses on both sides are released uniformly.
(2) When the rough machining on both sides of the part is completed, it is left for a few hours (generally 48H) so that the residual stress is fully released and then the finishing process is performed.
(3) When the part is milled on one side, try to take a small margin and multiple passes.
(4) Since the material has high strength and high toughness, it is necessary to control the depth of the knife, ensure sufficient cooling during cutting, and prevent deformation of the part due to cutting heat, and also pay attention to the hardness of the jig.
Generally, the following principles should be observed in the installation and fixture selection of aluminum workpieces:
(1) When the aluminum processing pieces are not in large quantities, combination clamps, adjustable clamps, and other universal clamps should be used as much as possible to shorten production preparation time and save production costs;
(2) Consider the use of special fixtures in batch production and strive for a simple structure;
(3) The loading and unloading of parts should be quick, convenient and reliable to shorten the pause time of the machine tool; Each component on the fixture should not interfere with the machining of the parts on the surface of the part, and the fixture can not affect the cutting in the process (such as collisions, etc.).

Aluminum alloy stamping
Aluminum alloy materials are soft, expensive, and easily broken. Some aluminum alloy products require further processing such as wire drawing and anodizing. In stamping production, it is particularly prone to produce: top injuries and scratches. Special attention must be paid to the following points in mold making:
1. For the case where the amount does not affect the project, the project at the back as far as possible punching punch. even for a product with a large number of punching holes, one more project may be considered and the punching may be ranked last.
2. The aluminum material is softer and the mold is easier to block material. Therefore, in designing the mold for clearance, a gap of 10% of the material thickness of the two sides should be placed. The straight-to-deep position of the blade is more suitable for 2 mm, and the taper is 0.8-1°.
3. During bending, aluminum chips are easily generated when the aluminum material is bent. It will cause spot injury and indentation. The aluminum raw material needs to be attached with PE film. In the case of rollers and plating, it is better to use hard chrome plating.